|Bending Material||2" and Above|
|Usage/Application||Used to remove fine practices and fluids from pipes|
|Surface Treatment||Paint Coated|
SPM Equipment is engages manufacturer and supplier of wide range of Pipe Pull Through. The SPM range of Pipe Pull Through also can be used for these cleaning and gauging operation and the Pipe Pull Through are designed to suit all manner of shackles and wire line tether. They consist of two thick rubber disc mountains on a high tensile steel central shaft with a towing eye at each end.
The Pipe Pull Through can be designed for light interference where there are unknown levels of debris and corrosion through to heavy duty pipe pull through, with aggressive scale removal systems. Our offered Pipe Pull Through also allowing detailed inspections after each Pipe pull through run.
|Pipe Diameter||6" to 20"|
|Bending Speed||3 to15 r/min|
SPM Equipment is leading manufacturer of Pipe Bending Machine. In pipe bending machine hydraulic control gives one operator complete command of all machine operation and calibrated indicator road allows operator to make consistently uniform bends.
Pipe bending machine comes with conversion kit conversion to another pipe size within machine range is made simply by fitting an alternative bending set. We are using high quality material to ensure long life without fatigue failer. Our bending machine requires a bending shoe, bending die and mandrel are required for each pipe size to be bent.
We are using high grade bending cylinder for getting great force and higher pressure rating. The higher capacity operating valve is mounted lower thus offering the operator easy access from the ground. The SPM pipe bending machine is designed for bending the carbon pipe of various thickness and diameters. Also give fully equipped control panel with automatic emergency shutdown that total control to the operator. The SPM pipe bending machine is enable to bend all grades of API-5L pipe within its range.
|Pipe Diameter (mm)||16" to 48" , 34" to 60"|
|Material||Mild Steel, Polyurethane|
|Application||For bending pipe in oil & Gas Project|
The Hydraulic Wedge Mandrel was developed specifically to meet the bending requirements of heavy-wall and high-yield grade pipe.
Part of SPM Equipment’ High-Productivity Bending System, the HWM is particularly successful in providing a smooth bend with no "out-of-round." Simple design and few parts result in low maintenance cost.
|Material||Mild Steel, PU|
|Size||16" to 48", 10" to 18" (Pipe Dia)|
Our Hydraulic Wedge Mandrel For Pipe Bending Machine are made of very high quality, high yield stainless steel for enhanced robustness and flexibility. They are supplied complete with extension pipes and sets of shims for registration.
|Usage/Application||Pipe Bending in Oil and Gas pipeline projects|
|Size||8 to 18 Inch|
Our pipe bending equipment is designed to be durable and hard wearing, needing only minimal maintenance and providing years of service. People you know. Equipment you trust. Experience SPM Equipment.
SPM Equipment offer wide range of the polyurethane disc plug mandrel gives 360 degree support to the inside surface of the pipe. Part of the SPM equipment standard bending system the polyurethane disc plug mandrel is effective in holding pipe “out of roundness” to a minimum. Allow more degree of bend without wrinkles. You can easily convert pipe size and wall thickness range within the model’s size. It’s simple, robust design reduces maintenance requirements and comes complete with all necessary hookup parts. This mandrel works with the SPM Equipment's pipe bending machine and other pipe bending machine as its power source.
Depending on its size, the hydraulic mandrel either is moved manually within the pipe using a reach rod. To operate the mandrel, the pull-type version requires two hydraulic hoses, whereas the self-propelled version requires four hydraulic hoses. The hydraulic mandrel is supplied directly over the bending machine’s hydraulic system.
|Size||8 inch to 18 inch|
|Usage/Application||Pipe Bending in Oil and Gas pipeline project|
|Size||16 to 48 Inch (Pipe Size)|
|Working Pressure||225 PSI|
The SPM Equipment's Hydraulic Wedge Type Pipe Bending Mandrel covers a range of diameters and is adjustable for wall thicknesses within the specified range of the mandrel. Adjustable any wall thicknesses within specified mandrel range can cover two pipe sizes through use of our conversion kits. Our Wedge Bending Mandrels are also available in both manual and motorized version.
SPM Equipment Wedge Bending Mandrel is engineered to meet the bending specifications of high grade pipe used in oil and gas pipeline projects.
Based on the pipe specifications (wall thickness) the mandrel is adjusted to the required setting by SPM Equipment.
The bending mandrel applies a powerful radial support to the inner walls, while remaining flexible lengthwise. This way a smooth bend is ensured and the diameter and roundness of the pipe are maintained.
|Usage/Application||Pipe Bending in Oil and gas pipeline projects|
|Length||300 mm to 1.25 meter|
|Surface Finishing||PU / Rubber Coated|
|Packaging Type||Carton Box|
|Pipe Diameter||6" to 48"|
SPM Equipmentis one of the leading manufacturers of Pipe Bending Die Set. Pipe bending shoe allow the bending machine to work with specific pipe size over a wide range of diameter. Pipe bending shoe polyurethane coated has protected the pipe. We even have special sets available on request. All SPM Equipment bending sets are designed and manufactured to conform to all API-5L pipe size.
Standard set consists of three pieces.